126.2936.39…ZWH3105-3125.qxd 24/10/08 09:01 Página 1
ZWH3105
ZWH3125
126.2936.39…ZWH3105-3125.qxd 24/10/08 09:01 Página 30
Safety information
In the interest of your safety and to ensure
the correct use, before installing and first
using the appliance, read this user manual
carefully, including its hints and warnings.
To avoid unnecessary mistakes and
accidents, it is important to ensure that all
people using the appliance are thoroughly
familiar with its operation and safety
features. Save these instructions and make
sure that they remain with the appliance if
it is moved or sold, so that everyone using
it through its life will be properly informed
on appliance use and safety.
● Always unplug the appliance and turn off
the water supply after use, cleanning and
maintenance.
● Under no circumstances should you attempt
to repair the machine yourself. Repairs
carried out by inexperienced persons may
cause injury or serious malfunctioning.
Contact your local Service Centre. Always
insist on genuine spare parts.
Installation
● This appliance is heavy. Care should be
taken when moving it.
● When unpacking the appliance, check that it
is not damaged. If in doubt, do not use it
and contact the Service Centre.
● All packing and transit bolts must be
removed before use. Serious damage can
occur to the product and to property if this is
not adhered to. See relevant section in the
user manual.
● After having installed the appliance, check
that it is not standing on the inlet and drain
hose and the worktop is not pressing the
electrical supply cable.
● If the machine is situated on a carpeted
floor, please adjust the feet in order to allow
air to circulate freely
General safety
● It is dangerous to alter the specifications or
attempt to modify this product in any way.
● During high temperature wash programmes
the door glass may get hot. Do not touch it!
● Make sure that small pets do not climb into
the drum. To avoid this, please check into
the drum before using.
● Any objects such as coins, safety pins,
nails, screws, stones or any other hard,
sharp material can cause extensive damage
and must not be placed into the machine.
● Only use the advised quantities of fabric
softener and detergent. Damage to the
fabric can ensue if you over-fill. Refer to the
manufacturer’s recommendations of
quantities.
● Always be sure, that there is no water
leakage from hoses and their connections
after the installation.
● Wash small items such as socks, laces,
washable belts etc in a washing bag or
pillow case as it is possible for such items
to slip down between the tub and the inner
drum.
● Do not use your washing machine to wash
articles with whalebones, material without
hems or torn material.
● If the appliance is installed in a location
subject to frost, please read the «dangers
of freezing» chapter.
● Any plumbing work required to install this
appliance should be carried out by a
qualified plumber or competent person.
● Any electrical work required to install this
appliance should be carried out by a
qualified electrician or competent person.
30
126.2936.39…ZWH3105-3125.qxd 24/10/08 09:01 Página 31
Use
Child safety
● This appliance is designed for domestic
use. It must not be used for purposes other
than those for which it was designed.
● Only wash fabrics which are designed to be
machine washed. Follow the instructions on
each garment label.
● Do not overload the appliance. See the
relevant section in the user manual.
● Before washing, ensure that all pockets are
empty and buttons and zips are fastened.
Avoid washing frayed or torn articles and
treat stains such as paint, ink, rust, and
grass before washing. Underwired bras
must NOT be machine washed.
● This washing machine is not intended for
use by young children or infirm persons
without supervision.
● Young children should be supervised to
ensure that they do not play with the
appliance.
● The packaging components (e.g. plastic
film, polystyrene) can be dangerous to
children - danger of suffocation! Keep them
out of children’s reach
● Keep all detergents in a safe place out of
children’s reach.
● Make sure that children or pets do not climb
into the drum.
● Garments which have been in contact with
volatile petroleum products should not be
machine washed. If volatile cleaning fluids
are used, care should be taken to ensure
that the fluid is removed from the garment
before placing in the machine.
● Never pull the power supply cable to
remove the plug from the socket; always
take hold of the plug itself.
● Never use the washing machine if the
power supply cable, the control panel, the
working surface or the base are damaged
so that the inside of the washing machine is
accessible.
31
126.2936.39…ZWH3105-3125.qxd 24/10/08 09:01 Página 32
Description of the appliance
1
Detergent dispenser drawer
2
Control panel
3
Door opening handle
4
Drain pump
5
Adjustable feet
Detergent dispenser drawer
Prewash
Wash
Fabric Softener
32
126.2936.39…ZWH3105-3125.qxd 24/10/08 09:01 Página 33
Control panel and functions
5
6
1
2
4
7
8
3
1
2
3
4
5
6
7
8
Programme selector dial and On/Off switch
Temperature selector
Spin reduction button
Options button
AquaCare button
Start/Pause button
Programme progress display
Delay Start button
33
126.2936.39…ZWH3105-3125.qxd 24/10/08 09:01 Página 34
Programme table
Programme
Cotton 90º-
Type of laundry
Options
Spin red., Rinse Hold,
AquaCare, Daily, Quick,
SuperQuick
,
White or colored, for example, workcloths, bedcloths,
tablecloths, etc
Cotton Eco
60º - 40º
Spin Red., Rinse Hold,
, AquaCare
White or colored, for example, t-shirts, bedcloths little
soiled, etc
Spin Red., Rinse Hold,
, AquaCare, Daily,
Quick, SuperQuick
Cotton + Prewash
90º - 40º
White heavy soiled, for example, workcloths..
Cotton Eco +
Prewash
90º - 40º
Spin Red., Rinse Hold,
, AquaCare
Program which combines eco with prewash
programmes.
Synthetic
60º -
Synthetic or mixed fabrics, underwear, blouses, etc
Synthetic or mixed fabrics heavy soiled.
Spin Red., Rinse Hold,
, AquaCare, Daily, Qu
Synthetic +
Prewash 60º - 40º
Easy Iron
60º -
Synthetic or mixed fabrics to be gentle washed and spun.
Delicates fabrics to be gentle washed.
Spin Red., Rinse Hold,
, Quick, AquaCare
Delicates
40º -
Special programme for hand washing fabrics (with the
"hand washing" care symbol).
Handwash
40º -
Spin Red., Rinse Hold,
Wool
40º -
Special programme for wool
Jeans
60º -
Special programme for jeans, jackets
Spin Red., Rinse Hold,
AquaCare,
Separate rinse cycle for hand washed items of cotton
fabric
Rinse
For emtying out the last rinse water in programmes with the Rinse Hold
Separate spin for cottons Spin Red.
For cancelling the wash programme which is running and for switching the machine off.
Drain
Spin
Off
34
126.2936.39…ZWH3105-3125.qxd 24/10/08 09:01 Página 35
Washing hints
Sorting the laundry
Maximum loads
Follow the wash code symbols on each
Recommended loads are indicated in the
garment label and the manufacturer’s washing programme charts.
instructions. Sort the laundry as follows:
whites, coloureds, synthetics, delicates,
woollens.
General rules:
Cotton, linen: drum full but not too tightly
packed;
Synthetics: drum no more than half full;
Delicate fabrics and woollens: drum no
more than one third full.
Temperatures
Washing a maximum load makes the most
efficient use of water and energy.
For heavily soiled laundry, reduce the load
size.
for normally soiled white cottons
and linen (e.g. tea cloths, towels,
tablecloths, sheets...)
90°
60°
for normally soiled, colour fast
garments (e.g. shirts, night
dresses, pyjamas....) in linen,
cotton or synthetic fibres and for
lightly soiled white cotton (e.g.
underwear).
Laundry weights
The following weights are indicative:
bathrobe
1200 g
napkin, tea cloth, lady's brief, blouse
quilt cover
sheet
pillow case, towelling towel, night dress
table cloth
man's shirt
100 g
700 g
500 g
200 g
250 g
200 g
600 g
100 g
for delicate items (e.g. net
curtains), mixed laundry
including synthetic fibres and
woollens bearing the label «pure
new wool, machine washable,
non-shrink».
30°-40°-Cold
man's pyjamas
men's underpanths
Before loading the laundry
Never wash whites and coloureds together.
Whites may lose their «whiteness» in the
wash.
New coloured items may run in the first wash;
they should therefore be washed separately
the first time.
Make sure that no metal objects are left in
the laundry (e.g. hair clips, safety pins,
pins). Button up pillowcases, close zip
fasteners, hooks and poppers. Tie any
belts or long tapes.
Remove persistent stains before washing.
Rub particularly soiled areas with a special
detergent or detergent paste.
Removing stains
Stubborn stains may not be removed by just
water and detergent. It is therefore advisable
to treat them prior to washing.
Blood: treat fresh stains with cold water. For
dried stains, soak overnight in water with a
special detergent then rub in the soap and
water.
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and
dab the stain; treat several times.
Dried grease stains: moisten with turpentine,
lay the garment on a soft surface and dab the
stain with the fingertips and a cotton cloth.
Grass: soap lightly and treat with bleach
(whites and fast coloureds only).
Treat curtains with special care. Remove
hooks or tie them up in a bag or net.
35
126.2936.39…ZWH3105-3125.qxd 24/10/08 09:01 Página 36
Rust: oxalic acid dissolved in hot water or a
rust removing product used cold. Be careful
with rust stains which are not recent since the
cellulose structure will have already been
damaged and the fabric tends to hole.
Mould stains: treat with bleach, rinse well
(whites and fast coloureds only).
Ball point pen and glue: moisten with
acetone (*), lay the garment on a soft cloth
and dab the stain.
The detergent and any additives must be
placed in the appropriate compartments of the
dispenser drawer before starting the wash
programme.
If using concentrated powder or liquid
detergents, a programme without prewash
must be selected.
Pour liquid detergent into the dispenser drawer
compartment marked
the programme.
just before starting
Lipstick: moisten with acetone as above, then Any fabric softener or starching additives must
treat stains with methylated spirits. Remove
any residual marks from white fabrics with
bleach.
be poured into the compartment marked
before starting the wash programme.
Follow the product manufacturer’s
recommendations on quantities to use and do
not exceed the «MAX» mark in the
detergent dispenser drawer.
Red wine: soak in water and detergent, rinse
and treat with acetic or citric acid, then rinse.
Treat any residual marks with bleach.
Ink: depending on the type of ink, moisten the
fabric first with acetone (*), then with acetic
acid; treat any residual marks on white fabrics
with bleach and then rinse thoroughly.
Tar stains: first treat with stain remover,
methylated spirits or benzine, then rub with
detergent paste.
Quantity of detergent to be used
The type and quantity of detergent will depend
on the type of fabric, load size, degree of
soiling and hardness of the water used.
Water hardness is classified in so-called
«degrees» of hardness. Information on
hardness of the water in your area can be
obtained from the relevant water supply
company.
(*) do not use acetone on artificial silk.
Detergents and additives
Good washing results also depend on the
choice of detergent and use of the correct
quantities to avoid waste and protect the
environment. Although biodegradable,
detergents contain substances which, in large
quantities, can upset the delicate balance of
nature.
Follow the product manufacturers’ instructions
on quantities to use.
Use less detergent if:
● you are washing a small load,
● the laundry is lightly soiled,
● large amounts of foam form during washing.
The choice of detergent will depend on the
type of fabric (delicates, woollens, cottons,
etc.), the colour, washing temperature and
degree of soiling.
All commonly available washing machine
detergents may be used in this appliance:
Degrees of water hardness
Degrees
Level Characteristic
German
°dH
French
°T.H.
1
2
3
4
soft
medium
hard
0-7
8-14
15-21
> 21
0-15
16-25
26-37
> 37
● powder detergents for all types of fabric,
● powder detergents for delicate fabrics (60°C
max) and woollens,
● liquid detergents, preferably for low
temperature wash programmes (60°C max) for
all types of fabric, or special for woollens only.
very hard
36
126.2936.39…ZWH3105-3125.qxd 24/10/08 09:01 Página 37
Before the first use
IMPORTANT!
WARNING!
Pour 2 litres of water into the main wash
Ensure that the electrical and water
connections comply with the installation
instructions.
compartment
of the detergent drawer in
order to activate the ECO valve. Then run a
cotton cycle at 95°C, without any laundry in
the machine, to remove any manufacturing
residue from the drum and tub. Pour 1/2 a
measure of detergent into the dispenser
drawer and start the machine.
IMPORTANT!
Remove the polystyrene block and any
material from the drum.
Operating sequence
1. Load the laundry
Open the door by
carefully pulling the
door handle outwards.
Place the laundry in
the drum, one item at
a time, shaking them
out
If required, pour fabric softener into the
compartment marked
(the amount used
must not exceed the «MAX» mark in the
drawer). Close the drawer gently.
3. Select the required programme
The selector dial
is divided into
following
as much as possible. Close the door.
sections:
2. Measure out the detergent and the fabric
softener
● Cottons,
● Synthetics,
● Special
The green Start/Pause light starts to flash.
The selector dial can be turned either
clockwise or anticlockwise.
Position «Off» to Reset programme/Switching
OFF of the machine.
At the end of the programme the selector
dial must be turned to position «Off», to
switch the machine off.
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent
required, pour it into the main wash
compartment
a programme with the prewash phase, pour it
into the compartment marked
and, if you wish to carry out
.
37
126.2936.39…ZWH3105-3125.qxd 24/10/08 09:01 Página 38
IMPORTANT!
5. Select the required temperature.
Turn the temperature
selector dial to select the
washing temperature.
Maximum temperatures
are 90°C for cottons,
60°-50°C for synthetic
fabrics and jeans, 40°C
for delicate fabrics, wool
If you turn the programme selector dial to
another programme when the machine is
working, the red Start/Pause pilot light will
flash 3 times to indicate a wrong selection.
The machine will not perform the new selected
programme.
4. Select the spin speed or No spin or
Rinse Hold option
Press the Spin
and fabrics to be hand-washed.
By selecting position (Cold) the machine
will wash with cold water. To be used for
extremely delicate items, such as curtains.
button repeatedly
to change the
spin speed, if you
want your laundry
to be spun at a
speed different
from the one
6. Select Daily, Quick or SuperQuick option
Press the «Options» button
repeatedly, to select only one of
the available options. The
relevant light will light up.
proposed by the
Press the Options button
repeatedly, to select the
desired option. The relevant
light will light up.
appliance.
The relevant light will light up.
Maximum speeds are:
● Cotton and Jeans: 1000 or 1200 rpm
depending on the model;
You can select 4 different options:
DIARIO (Daily): to be used for cotton, synthetic
or delicate items of daily use in order to obtain
good washing performance in a short time.
RÁPIDO (Quick): a short cicle for items lightly
soiled.
SUPER RÁPIDO (Extra Quick): a very short
cycle for items that have been used for a short
time or wash at half load.
Diario, Rápido y Super options cannot be
used with the Economy programme 60 Eco
and 40 Eco.
If an option which is not compatible with the
set wash programme is selected, the message
Err is displayed for about 2 seconds and the
red pilot light of the Start/Pause button will
flash 3 times.
● Synthetic and Handwash: 900 rpm
● Delicates: 700 rpm;
No spin
: By selecting this option, all
spinning phases are suppresed. On Cotton,
Synthetic and Delicates programmes, the rinses
will be performed with more water.
Rinse Hold: by selecting this option the water
of the last rinse is not emptied out to prevent the
fabrics from creasing. When the programme has
finished the pilot lights «Door» and «End» are
lit, the Start/Pause and «Wash» lights are off
and the door is locked to indicate that the water
must be emptied out..
To empty out the water:
1. turn the programme selector dial to «Off»
2. select the Drain or Spin programme
3. reduce the spin speed if needed, by means
of the relevant button
4. depress Start/Pause button
5. at the end of programme, only the pilot light
End comes on.
38
126.2936.39…ZWH3105-3125.qxd 24/10/08 09:01 Página 39
IMPORTANT!
8. Select the Delay Start
If an option is chosen that is not allowed with
the selected programme, the red pilot light of
the Start/Pause button will flash 3 times.
Before you start
the programme, if
you wish to delay
the start, press the
Delay Start button
repeatedly, to
The washing time will be reduced according to
the type of fabric and the selected temperature.
7. Select the AquaCare option
select the desired
delay.
This button can be selected
with all programmes except
the Hand wash
programmes. The machine
performs some additional
The relevant light illuminates.
This button makes it possible to delay the
starting of the washing programme by 3, 6, or
9 hours.
You must select this option after you have set
the programme and before you press the
Start/Pause button.
You can cancel the delay time at any moment,
before you press the Start/Pause button.
If you have already pressed the Start/Pause
button, and you wish to cancel the delay time,
proceed as follows:
• set the washing machine to PAUSE by
pressing the Start/Pause button;
• press the Delay Start button once, the light
relevant to the selected delay goes off.
• press the Start/Pause button again to start
the programme.
rinses.
This option is recommended
for people who are allergic to detergents, and in
areas where the water is very soft.
8. Select the Start/Pause
To start the selected programme, press the
Start/Pause button; the corresponding green
pilot light stops flashing.
The «Wash» and
«Door» lights are alight
to indicate that the
appliance starts
operating and the door
is locked.
IMPORTANT!
• The selected delay can be changed only
after selecting the washing programme
again.
To interrupt a programme which is running,
depress the Start/Pause button: the
corresponding green pilot light starts to flash.
To restart the programme from the point at
which it was interrupted, press the Start/Pause
button again.
• The door will be locked throughout the delay
time. If you need to open the door, you must
first set the washing machine to PAUSE by
pressing the Start/Pause button and then
wait about 2 minutes until the «Door» light
has gone off. After you have closed the door,
press the Start/Pause button again.
The Delay Start can not be selected with
Drain programmes.
If you have chosen a delayed start, the machine
will begin the countdown.
IMPORTANT!
If an incorrect option is selected, the red
pilot light of the Start/ Pause button flashes
for 3 times.
39
126.2936.39…ZWH3105-3125.qxd 24/10/08 09:01 Página 40
Programme progress display
Cancelling a programme
After having depress Start/Pause button, the
«Wash» pilot light illuminates and stays on
while the machine is working.
Turn the selector dial to Off to cancel a
programme which is running. Now you can
select a new programme.
Opening the door after the programme has
started
First set the machine to pause by pressing the
Start/Pause button.
If the «Door» light flashes and after 2 minutes
goes off, the door can be opened.
If the «Door» light does not flash, this means
that the machine is already heating, that the
water level is above the bottom edge of the
door or that the drum is turning.
The «Door» pilot light indicates if the door can
be opened:
• light on: the door cannot be opened.
The appliance is running.
• light off: the door can be opened.
The washing programme is finished.
• flashing light: the door is opening.
When the programme has finished, the «End»
pilot light illuminates and the «Wash» light
goes off.
In this case the door can not be opened.
If you cannot open the door but you need to
open it you have to switch the machine off by
turning the selector dial to «Off».
After about 2 minutes the door can be opened
(pay attention to the water level and
temperature!).
Altering an option or a running programme
At the end of the programme
It is possible to change any option before the
programme carries it out. Before you make
any change, you must pause the washing
machine by pressing the Start/Pause button.
Changing a running programme is possible
only by resetting it. Turn the programme
selector dial to Off and then to the new
The machine stops automatically. The
Start/Pause and «wash» lights go off and the
«end» phase light illuminates. The door can
be opened (the Door light is off).
If the «Rinse Hold» option has been selected,
the «end» and «door» lights illuminates but
programme position. The washing water in the the door remains locked to indicate that the
tub will not emptied out. Start the new
programme by depressing the Start/Pause
button again.
water must be emptied out before opening the
door.
To empty out the water please read the steps
on the Rinse Hold option paragraph.
Turn the programme selector dial to «Off» to
switch the machine off. Remove the laundry
from the drum and carefully check that the
drum is empty.
If you do not intend to carry out another wash,
close the water tap. Leave the door open to
prevent the formation of mildew and
unpleasant smells.
Interrupting a programme
Depress the Start/Pause button to interrupt a
programme which is running, the
corresponding light starts to flash. Depress the
button again to restart the programme.
40
126.2936.39…ZWH3105-3125.qxd 24/10/08 09:01 Página 41
Care and cleaning
IMPORTANT!
Cleaning the drawer recess
You must DISCONNECT the appliance from
the electricity supply, before you can carry out
any cleaning or maintenance work.
Having removed the
drawer, use a small
brush to clean the
Descaling
recess, ensuring that all
washing powder residue
is removed from the
upper and lower
The water we use normally contains lime. It is a
good idea to periodically use a water softening
powder in the machine. Do this separately from
any laundry washing, and according to the
softening powder manufacturer's instructions. This
will help to prevent the formation of lime deposits.
part of the recess.
Replace the drawer and run the rinse programme
without any clothes in the drum.
Maintenance Wash
Cleaning the pump
With the use of low temperature washes it is
possible to get a build up of residues inside
the drum.
We recommend that a maintenance wash be
performed on a regular basis.
To run a maintenance wash:
The pump should be inspected if
●
the machine does not empty and/or spin
the machine makes an unusual noise during
draining due to objects such as safety pins,
coins etc. blocking the pump.
●
Proceed as follows:
●
●
●
The drum should be empty of laundry.
Select the hottest cotton wash programme.
Use a normal measure of detergent, must
be a powder with biological properties.
●
Pull out the plug from the power socket.
If necessary, wait until the water has cooled
down.
●
●
Open the drainage area door.
External cleaning
Clean the exterior cabinet of the appliance with
soap and water only, and then dry thoroughly.
●
Place a bowl to collect
the water.
Turn slowly the lid of
the diaphragm
●
Cleaning the dispenser drawer
towards left side and
allow that the water of
the washing machine
goes flowing slowly to
the bowl.
The washing powder and additive dispenser
drawer should be cleaned regularly.
●
●
●
●
When the bowl is full, turn and close the lid of
the diaphragm.
Empty the bowl. Repeat the procedure until you
have completely emptied the washing machine.
Always keep a rag nearby to dry up spillage of
water when removing the cover.
Remove the objects such as buttons, coins and
the lint that has been accumulated in the
area of the pump impeller by rotating it.
To aid cleaning, the top part of the additive
compartment should be removed.
Remove the drawer by pressing the catch
downwards and by pulling it out. Flush it out
under a tap, to remove any traces of
accumulated powder.
41
126.2936.39…ZWH3105-3125.qxd 24/10/08 09:01 Página 42
●
●
Screw the lid of the diaphragm clockwise, be The dangers of freezing
sure is completely tighten.
If the machine is exposed to temperatures
Close the drainage area door.
below 0°C, certain precautions should be
taken.
●
●
●
Turn off the water tap.
Unscrew the inlet hose.
Place the end of the inlet hose in a bowl
placed on the floor and let water drain out.
Screw the water inlet hose back on.
When you intend to start the machine up
again, make sure that the room temperature
is above 0°C.
●
●
IMPORTANT!
Every time you drain the water through the
emergency emptying hose you must pour 2
litres of water into the main wash
compartment of the detergent drawer and then
run the drain programme. This will activate the
ECO VALVE device avoiding that part of the
detergent remains unused at next washing.
IMPORTANT!
Emergency emptying out
If the water is not discharged, proceed as
follows to empty out the machine:
When the appliance is in use and depending
on the programme selected there can be hot
water in the pump.
Never remove the pump cover during a wash
cycle, always wait until the appliance has
finished the cycle, and is empty. When
replacing the cover, ensure it is securely
retightened so as to stop leaks and young
children being able to remove it.
●
●
●
pull out the plug from the power socket;
close the water tap;
if necessary, wait until the water has cooled
down;
open the pump door;
clean the pump if necessary as previously
described;
●
●
Cleaning the water inlet filter
If your water is very hard or contains traces of
lime deposit, the water inlet filter may become
clogged.
●
screw the pump cover again and close the
door.
It is therefore a good idea to clean it from time
to time.
Turn off the water
tap. Unscrew the
water inlet hose.
Clean the filter using
a hard bristle brush.
Tighten up the inlet
hose.
42
126.2936.39…ZWH3105-3125.qxd 24/10/08 09:01 Página 43
Something not working
IMPORTANT!
Certain problems are due to lack of simple maintenance or oversights, which can be solved
easily without calling out an engineer. Before contacting your local Service Centre, please carry
out the checks listed below.
During machine operation it is possible that the red Start/Pause pilot light flashes to indicate that
the machine is not working.
Once the problem has been eliminated, press the Start/Pause button to restart the programme. If
after all checks, the problem persists, contact your local Service Centre.
Malfunction
Possible Cause / Solution
The door has not been closed. (Red Start/Pause
pilot light flashes)
• Close firmly the door.
The plug is not properly inserted in the power
socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The washing machine does not start:
The main fuse has blown.
• Replace the fuse.
The selector dial is not correctly positioned and the
Start/Pause button has not been depressed.
• Please turn the selector dial and press the
Start/Pause button again.
The delay start has been selected.
• If the laundry are to be washed immediately,
cancel the delay start
The water tap is closed. (Red Start/Pause pilot
light flashes)
• Open the water tap.
The inlet hose is squashed or kinked.
(Red Start/Pause pilot light flashes)
• Check the inlet hose connection.
The machine does not fill:
The filter in the inlet hose is blocked.
(Red Start/Pause pilot light flashes)
• Clean the water inlet hose filter.
The door is not properly closed.
(Red Start/Pause pilot light flashes)
• Close firmly the door.
43
126.2936.39…ZWH3105-3125.qxd 24/10/08 09:01 Página 44
Malfunction
Possible Cause / Solution
The end of the drain hose is too low.
• Refer to relevant paragraph in «water drainage»
section.
The machine fills then empties
immediately:
The drain hose is squashed or kinked.
(Red Start/ Pause pilot light flashes)
• Check the drain hose connection.
The drain pump is clogged.
(Red Start/Pause pilot light flashes)
• Clean the drain pump.
The machine does not empty and/or
does not spin:
The option Rinse Hold or
.has been selected.
• Select the Drain or Spin programmes
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
Too much detergent or unsuitable detergent (creates
too much foam) has been used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the
inlet hose fittings. It is not always easy to see this as
the water runs down the hose; check to see if it is
damp.
There is water on the floor:
• Check the water inlet hose connection.
The inlet hose is damaged.
• Change it with a new one.
Too little detergent or unsuitable detergent has been
used.
• Increase the detergent quantity or use another
one.
Stubborn stains have not been treated prior to
washing.
• Use commercial products to treat the stubborn
stains.
Unsatisfactory washing results:
The correct temperature was not selected.
• Check if you have selected the correct
temperature.
Excessive laundry load.
• Introduce into the drum less laundry.
44
126.2936.39…ZWH3105-3125.qxd 24/10/08 09:01 Página 45
Malfunction
Possible Cause / Solution
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released.
• Wait about 2 minute.
The door will not open:
There is water in the drum.
• Select drain or spin programme to empty out the
water.
The transit bolts and packing have not been
removed.
• Check the correct installation of the appliance.
The support feet have not been adjusted.
• Check the correct levelling of the appliance.
The machine vibrates or is noisy:
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
Maybe there is very little laundry in the drum.
• Load more laundry.
The electronic unbalance detection device has cut in
because the laundry is not evenly distributed in the
drum. The laundry is redistributed by reverse rotation
of the drum. This may happen several times before
the unbalance disappears and normal spinning can
resume. If, after 10 minutes, the laundry is still not
evenly distributed in the drum, the machine will not
spin. In this case, redistribute the load manually and
select the spin programme.
Spinning starts late or the machine
does not spin:
●
Redistribute the laundry.
The machine is fitted with a type of motor which
makes an unusual noise compared with other
traditional motors. This new motor ensures a softer
start and more even distribution of the laundry in the
drum when spinning, as well as increased stability of
the machine.
The machine makes an unusual
noise
Machines based on modern technology operate very
economically using very little water without affecting
performance.
No water is visible in the drum
If you are unable to identify or solve the
problem, contact our service centre.
Before telephoning, make a note of the model,
serial number and purchase date of your
machine: the Service Centre will require this
information.
Mod. ... ... ...
Prod. No. ... ... ...
Ser. No. ... ... ...
45
126.2936.39…ZWH3105-3125.qxd 24/10/08 09:01 Página 46
Technical data
Dimensions
Width
Height
60 cm
85 cm
64 cm
Depth (inclunding the porthole)
Electrical connection Voltage -
Overall power - Fuse
Information on the electrical connection is given on the rating
plate on the inner edge of the appliance door
Water supply pressure
Minimum
Maximum
0,05 MPa
0,8 MPa
Maximum Load
Spin Speed
7
kg
Mod. ZWH3105
Mod. ZWH3125
1000 rpm
1200 rpm
Maximum
Consumption values
Programme
duration
(in minutes)
Energy
consumption
(in kWh)
Water
consumption
(in litres)
Programme
Cotton 90º
155
160
140
90
2.15
1.19
1.47
0.97
0.87
0.72
0.47
0.35
0.55
0.27
-
71
59
63
56
60
64
58
52
58
47
-
Cotton 60º Eco (*)
Cotton 60º - Cold
Synthetic 60º - Cold
Easy Iron 40º
Delicates 40º - Cold
Hanwash 30º - Cold
Wool 40º
96
65
60
60
Jeans 40º
153
54
Rinses
Drain
2
Spin
12
-
-
Infos
(*) The “Cottons 60° Eco” is the
reference programme for the
data entered in the energy
label, in compliance with
EEC 92/75 standards.
The consumption data shown on this chart is to be considered purely
indicative, as it may vary depending on the quantity and type of laundry,
on the inlet water temperature and on the ambient temperature. It refers
to the highest temperature for each wash programme.
46
126.2936.39…ZWH3105-3125.qxd 24/10/08 09:01 Página 47
Installation instruction
Positioning
Install the machine on a flat hard floor. Make
Transit security bars
Before starting the machine up, the transport
security bars must be removed as follows:
You are advised to keep all the transport
security bars. In case the appliance has to be
transported again.
sure that air circulation around the machine is
not impeded by carpets, rugs etc. Check that
the machine does not touch the wall or other
kitchen units. Level the washing machine by
raising or lowering the feet. Once in the right
position fix the feet by pushing the nuts
against the base of the case. The feet may be
tight to adjust as they incorporate but the
machine MUST be level and stable.
If necessary, check the setting with a spirit
level.
Accurate levelling prevents vibration, noise
and displacement of the machine during
operation.Never place cardboard, wood or
similar materials under the machine to
compensate for any unevenness in the floor.
Some vibration is inevitable, especially if
mounted on a wooden floor.
1. Unscrew and remove the three rear screws
by means of a key.
Make sure the hoses are not squashed.
Sprung wooden floors are particularly
susceptible to vibration. For advice, consult a
builder. If possible, always place the machine
on a solid floor.
2. Open the porthole and remove the
polystyrene block fitted with adhesive tape
on the door seal.
3. Place the machine in an upright position
and remove the three plastic bolts.
5. Plug the 3 holes with the plastic plugs
which you can find in the envelope
containing the instruction booklet.
47
126.2936.39…ZWH3105-3125.qxd 24/10/08 09:01 Página 48
Water inlet
The appliance must be connected to a cold
water supply.
There should be a COLD WATER tap near the
washing machine with a screwing on
connection pipe of 3/4" for the water supply, a
sink, a wash basin or a drainage system in the
wall.
Previously check if:
- it is not a hot water tap.
- the running water is clean. If not, run off a
reasonable amount of water to flush out any
debris that may have collected in the pipes.
Have the permanent drainage system in the
wall checked by a plumber.
A minimum water pressure of 0.05 MPa (0.5
bar) is required for safe operation of the
appliance.
If you cannot make the cold water connection
direct from the rising mains, you may be able
to operate the appliance from your cold water
storage system.
There should be a minimum distance of 5.02m
(16.5 ft) between the appliance’s inlet and the
bottom of the water storage tank.
Electrical connection
1. Connect the hose to a tap with a 3/4”
thread. Always use the hose supplied with
the appliance. The inlet hose must not be
lengthened. If it is too short and you do not
wish to move the tap, you will have to
purchase a new, longer hose specially
designed for this type of use.
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
WARNING!
This appliance must be earthed.
The manufacturer declines any liability
should this safety measure not be
observed.
Before switching on, make sure the electricity
supply voltage is the same as that indicated
on the appliance’s rating plate.
NOTE
Installation should
comply with local
water authority and
building regulations’
requirements.
IMPORTANT!
Information on the electrical connection is
given on the rating plate on the inner edge
of the appliance door.
2. If necessary turn the hose adequately by
unscrewing the nut at the rear of the
appliance. Now tighten the nut anew to
avoid leaks. (Open the tap and assure that
it does not leak and close it again.)
The appliance is supplied with a 13amp plug
fitted. In the event of having to change the
fuse in the plug supplied, a 13amp ASTA
approved (BS1363/A) fuse must be used.
Should the plug need to be replaced for any
reason, proceed as described below.
48
126.2936.39…ZWH3105-3125.qxd 24/10/08 09:01 Página 49
Environmental concerns
Packaging materials
Ecological hints
The materials marked with the symbol
recyclable.
>PE<=polyethylene
>PS<=polystyrene
>PP<=polypropylene
This means that they can be recycled by
disposing of them properly in appropriate
collection containers.
are
To save water, energy and to help protect the
environment, we recommend that you follow
these tips:
●
Normally soiled laundry may be washed
without prewashing in order to save
detergent, water and time (the environment
is protected too!).
●
●
The machine works more economically if it
is fully loaded.
Old machine
Use authorised disposal sites for your old
appliance. Help to keep your country tidy!
With adequate pre-treatment, stains and
limited soiling can be removed; the laundry
can then be washed at a lower temperature.
Measure out detergent according to the
water hardness, the degree of soiling and
the quantity of laundry being washed.
The symbol
on the product or on its
●
packaging indicates that this product may not
be treated as household waste. Instead it shall
be handed over to the applicable collection
point for the recycling of electrical and
electronic equipment. By ensuring this product
is disposed of correctly, you will help prevent
potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product. For more detailed
information about recycling of this product,
please contact your local city office, your
household waste disposal service or the shop
where you purchased the product.
49
126.2936.39…ZWH3105-3125.qxd 24/10/08 09:01 Página 50
Guarantee conditions
Standard guarantee conditions
European Guarantee
We, Electrolux, undertake that if within 12
months of the date of the purchase this
Electrolux appliance or any part thereof is
proved to be defective
This appliance is guaranteed by Electrolux in
each of the countries listed at the back of this
user manual, for the period specified in the
appliance
by reason only of faulty workmanship or
materials, we will, at our option repair or
replace the same FREE OF CHARGE for
labour, materials or carriage on condition that:
guarantee or otherwise by law. If you move from
one of these countries to another of the
countries listed below the appliance guarantee
will move
●
●
●
The appliance has been correctly installed
and used only on the electricity supply
stated on the rating plate.
The appliance has been used for normal
domestic purposes only, and in accordance
with the manufacturer’s instructions.
The appliance has not been serviced,
maintained, repaired, taken apart or
tampered with by any person not authorised
by us.
Electrolux Service Force Centre must
undertake all service work under this
guarantee
Any appliance or defective part replaced
shall become the Company’s property.
This guarantee is in addition to your
statutory and other legal rights.
with you subject to the following qualifications:
●
The appliance guarantee starts from the date
you first purchased the appliance which will
be evidenced by production of a valid
purchase document issued by the seller of
the appliance.
●
The appliance guarantee is for the same
period and to the same extent for labour and
parts as exists in your new country of
residence for this particular model or range of
appliances.
●
●
●
The appliance guarantee is personal to the
original purchaser of the appliance and
cannot be transferred to another user.
The appliance is installed and used in
accordance with instructions issued by
Electrolux and is only used within the home,
i.e. is not used for commercial purposes.
The appliance is installed in accordance with
all relevant regulations in force within your
new country of residence.
●
●
Exclusions
●
●
Damage or calls resulting from
transportation, improper use or neglect, the
replacement of any light bulbs or removable
parts of glass or plastic.
Costs incurred for calls to put right an
appliance which is improperly installed or
calls to appliances outside the United
Kingdom.
The provisions of this European Guarantee do
not affect any of the rights granted to you by
law."
●
●
●
Appliances found to be in use within a
commercial environment, plus those which
are subject to rental agreements.
Products of Electrolux manufacturer that are
not marketed by Electrolux.
50
|