WINEGARD®
ENTERTAINMENT SELECT
MODEL VS-0503/VS-5312
Model shown has five inputs, three outputs.
FEATURES:
•
Simple push button controls allow you to send signals
•
Low profile housing blends
nicely with other electronic
components; fits easily in
overhead cabinets.
from any one of 5 different inputs to 2 TVs and VCR.
5 Inputs are Satellite Receiver, TV Antenna, VCR,
Cable TV & Auxiliary.
•
•
•
Shielded circuitry for high
isolation and low signal loss.
Oversize, easy-to-read graphics
for proper function selection
when mounted in out of the way
locations.
•
•
3 Outputs: Main TV, TV 2, VCR.
Built-in +12 VDC TV antenna power supply eliminates
need for separate wall mounted TV antenna power supply.
Self-resetting fuses used in antenna power supply
prevent failure caused by shorted connections.
•
•
Video switch allows for independent viewing of
signals at different TVs, with a record option from VCR.
OPERATION
Once all the connections have been properly made to the control box, you are ready to watch your
favorite programming.
USING THE BUTTONS ON THE FRONT OF THE CONTROL BOX
VIEWING
STEP 1. To view signals from an amplified TV Antenna, first press the TV Antenna POWER button to the
ON position. This provides +12 volt power to the TV antenna amplifier located inside the antenna
housing. To view the TV antenna signal on the main TV, simply press the TV ANT button located above
the area marked “MAIN TV.” Follow the same procedure for TV 2.
NOTE: The picture quality from your outdoor TV antenna varies depending on the location of the TV
station in relationship to your location. If picture quality is degraded and you are not using an external
power supply, try turning the TV Antenna Power button on your control box Off and On, If your TV
antenna is powered by an external wall mounted power supply, try turning it Off and On.
STEP 2. To view Satellite signals on your main TV, press the SAT button above the area marked “Main
TV.” Follow the same procedure for TV 2.
STEP 3. To view Cable TV signals on your main TV, press the Cable TV button above the area marked
“Main TV.” Follow the same procedure for TV 2.
NOTE: To view Cable TV signals, you must be connected to a Cable TV input on the outside of
your vehicle. Cable TV inputs are available at many of today’s campgrounds.
STEP 4. To view VCR signals on your main TV, press the VCR button above the area marked “Main TV.”
Follow the same procedure for TV 2.
STEP 5. To view Auxiliary signals, such as games, camcorder, etc., on your main TV, press the AUX
button above the area marked “Main TV.” Follow the same procedure for TV 2.
RECORDING
STEP 6. To record programming from the Antenna, Satellite Antenna, Cable TV or Auxiliary, simply
press the appropriate button above the section marked VCR.
To record programming from the TV antenna to your VCR, press the TV ANT button above the VCR
section on the switch box.
To record programming from the Satellite antenna to your VCR, press the SAT button above the VCR
section on the switch box.
To record programming from an Auxiliary device to your VCR, press the AUX button above the VCR
section.
To record programming from Cable TV to your VCR, press the Cable TV button above the VCR section
on the switch box.
NOTE: To record Cable TV signals, you must be connected to a Cable TV input on the outside of
your vehicle. Cable TV inputs are available at many campgrounds.
NOTE: With Winegard’s control box, you can watch different programming on each of your two TV sets
while recording another program on your VCR. If your vehicle is equipped with an exterior patio TV set,
you may choose the programming source desired for the patio TV by using the buttons above the TV 2
section on the control box. The programming source is the same for the patio (exterior) TV and TV 2.
When viewing signals on the patio TV, you cannot view different signals on TV 2. You could watch
different signals on the main TV.
TROUBLESHOOTING
If the unit doesn’t switch properly between inputs, ( TVs, VCR, SAT, CABLE, etc.), be sure the coax is connected to
the proper jacks on the back of the control box. Make sure the center conductors of the coax cables are not bent and
are making good contact. See “Installing Coax Connectors” below.
If you are using the +12 VDC and light does not turn ON when pushing the power button, go through the following
steps.
1. Be sure the unit is wired into a +12 VDC source and that this source is supplying power to the plug going to
the control box. Check to make sure all connections are correct.
2. If power is being supplied to the control box and the light still does not go on when pushing the TV Antenna
Power Button, disconnect the coax from the jack labeled “From Antenna” on the back of the control box. If
the light now comes on, there is a short in your coax cable going to the outside antenna, or the amplifier in
your antenna is bad.
3. Reattach the coax cable to back of the control box. Disconnect it at the TV antenna. If the light comes on,
the coax cable is connected properly and the problem is in the antenna. If the light does not come on, the
problem is in the coax cable.
NOTE: The picture quality from your outdoor TV antenna varies depending on the location of the TV station in relationship to your
location. If picture quality is degraded and you are not using an external power supply, try turning the TV Antenna Power button on
your control box Off and On, If your TV antenna is powered by an external wall mounted power supply, try turning it Off and On.
INSTALLING COAX CONNECTORS
1. Strip outer cover back ½” from end of cable. Fray braid back as far as outer cover will allow.
2. Trim braid close to outer cover and remove ¼” of inner insulation. Be careful not to nick center conductor and make
sure no foil or braid can touch center conductor.
3. Slide connector tip between braid and inner insulation (braid and foil, on foil shield cable), and push connector on cable as
far as it will go. Crimp built-in ferrule with appropriate crimping tool. Do not crush cable out-of-round. (If you are
installing in very hot weather, increase these dimensions 1/8”).
WINEGARD MOBILE PRODUCTS LIMITED WARRANTY (2 YEARS PARTS; 1 YEAR LABOR)
Winegard Company warrants this Winegard product against defects in materials or workmanship for a period of two (2) years from date of original purchase.
During year one (1) of such warranty, Winegard Company will also pay authorized labor costs to an authorized Winegard dealer to repair or replace defective
products. No warranty claim will be honored unless at the time the claim is made, Customer presents proof of purchase to an authorized Winegard dealer, (to locate
the nearest authorized Winegard dealer, contact Winegard Company, 3000 Kirkwood Street, Burlington, IA 52601, Telephone 319-754-0600 or visit
www.winegard.com. Customer must provide proof of purchase with a dated sales receipt for the Winegard product to verify the product is under warranty. If the date
of purchase cannot be verified, the warranty period shall be considered to begin thirty (30) days after the date of manufacture.
If a defect in material or workmanship is discovered, Customer may take the product to an authorized Winegard dealer for service. Customer must provide proof
of purchase to verify the product is under warranty. If the product is brought to an authorized Winegard dealer for service prior to expiration of year one (1) of the
warranty period and a defect in material or workmanship is verified by Winegard Technical Services, Winegard Company will cover the Winegard dealer’s labor
charges for warranty service. The Winegard dealer must contact Winegard Technical Services in advance for pre-approval of the service. Approval of the service is at
the sole discretion of Winegard Company.
Alternatively, Customer may ship the product prepaid to Winegard Technical Services (located at 3000 Kirkwood Street, Burlington, Iowa 52601, Telephone
319-754-0660). Customer must return the product along with a brief description of the problem and provide Winegard Technical Services with Customer’s name,
address, and phone number. Customer must also provide proof of purchase to verify the product is under warranty. If the product is returned before the expiration of
the warranty period, Winegard Company will (at its option) either repair or replace the product.
This Limited Warranty does not apply if the product has been damaged, deteriorates, malfunctions or fails from: improper installation, misuse, abuse, neglect,
accident, tampering, modification of the product as originally manufactured by Winegard in any manner whatsoever, removing or defacing any serial number, usage
not in accordance with product instructions or acts of nature such as damage caused by wind, lightning, ice or corrosive environments such as salt spray and acid
rain.
RETURN AUTHORIZATION POLICY
A Return Material Authorization (RMA) is required prior to returning any product to Winegard Company or Winegard Warranty Services under this warranty
policy. Please call our Technical Services Department at (800) 788-4417 or send an email to [email protected] to obtain the RMA number. Please furnish the
date of purchase when requesting an RMA number. Enclose the product in a prepaid package and write the RMA number in large, clear letters on the outside of the
package. To avoid confusion or misunderstanding, a shipment(s) without an RMA number(s) or an unauthorized return(s) will be refused and returned to Customer
freight collect.
WINEGARD COMPANY DOES NOT ASSUME ANY LIABILITIES FOR ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, MADE BY ANY OTHER
PERSON.
ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE
AND MERCHANTABILITY ARE LIMITED TO THE TWO YEAR PERIOD OF THIS WARRANTY.
In states that do not allow limitations on implied warranties, or the exclusion of limitation of incidental or consequential damages, the above limitations or
exclusions do not apply.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion of limitation of incidental or consequential damages, so the above
limitations or exclusions may not apply to you.
This warranty gives Customer specific legal rights. Customer may also have other rights that may vary from state to state.
SATELLITE RECEIVER WARRANTY
See manufacturer’s limited warranty policy.
Winegard Company, 3000 Kirkwood St., Burlington, IA 52601, 319/754-0600, Fax 319/754-0787 www.winegard.com 2451991 Rev.1/06
|